MIO07 Detailed Description

Port Reference Table

In case you want to address the services of the MIO07 via IP:Port, you can use the following table to find the correct port number:

Port Function
10000 Binary I/O

Binary I/Os

Features

The MIO07 has a binary I/O function block providing 16 IEC 61131-2 compliant channels, corresponding to 16 I/O pins.

  • 4 galvanically isolated groups, each with 4 channels
  • Each pin can be used as a
    • binary output with read-back
    • binary input
  • Each channel configured as an output can switch the load to ground or to supply
  • Supply voltage of each group may be between 17VDC and 36VDC. Each group may use a different supply voltage.
  • Switching capability of each pin is 300mA for the high side switch and 200mA for low side switch.
  • Input circuit IEC 61131-2 Type 1/3 compliant, each pin draws 2.3mA (typ) to ground.
  • Switching level of the input is 6.7V to 8V, with 1.2V hysteresis
  • Per-Channel LED that reflects the input state. In case of overcurrent or overload on a channel, LED is flashing fast.
  • Configurable output watchdog, to reset outputs in case host application crashed
  • Max. Input Acquisition Frequency for Stream: 500Hz
  • Max. Output Frequency: 20Hz (limited by the io4edge direct I/O interface)

Channel Principles

Binary I/O Channel Pricnciple

Connection

Each binary I/O group has its own connector with the following pinout:

Pin Symbol Description
1 + Positive Supply Voltage
2 IO1 First I/O pin of the group
3 IO2 Second I/O pin of the group
4 IO3 Third I/O pin of the group
5 IO4 Fourth I/O pin of the group
6 - Supply Voltage Ground

Mating connectors for MIO07:

Use Cases

How to Connect the Load

Load may be connected to ground (high side switch) or to supply (low side switch). Be aware that high side switch can drive stronger current (300mA) than the low side switch (200mA).

Connect Load

Using Inputs

In case you want to use a pin as input, you can

  • monitor a switch to that is connected to supply
  • monitor a voltage source, referenced to ground

The switching level of the input is 6.7V to 8V, with 1.2V hysteresis.

Use Inputs

Using the io4edge API to access the Binary I/Os

First, install the io4edge client library.

Want to have a quick look to the examples? See our Github repository.

First, install the io4edge client library.

Want to have a quick look to the examples? See our Github repository.

Connect to the binary I/O function

To access the binary I/Os, create a Client and save it to the variable c. Pass as address either a service address or an ip address with port. Examples:

  • As a service address: MI07-1-binio
  • As an IP/Port: 192.168.201.1:10000

We need this client variable for all further access methods.

import (
  "time"
  "log"
  binio "github.com/ci4rail/io4edge-client-go/binaryiotypec"
  biniopb "github.com/ci4rail/io4edge_api/binaryIoTypeC/go/binaryIoTypeC/v1alpha1"
)

func main() {
    c, err := binio.NewClientFromUniversalAddress(address, time.Second)
    if err != nil {
        log.Fatalf("Failed to create binio client: %v\n", err)
    }
}

To access the binary I/Os, create a Client and save it to the variable binio_client. Pass as address either a service address or an ip address with port. Examples:

  • As a service address: MI07-1-binio
  • As an IP/Port: 192.168.201.1:10000

We need this client variable for all further access methods.


import io4edge_client.binaryiotypec as binio
import io4edge_client.functionblock as fb

def main():
  binio_client = binio.Client(address)

Configure the binary I/Os

The binary I/Os can be configured as input or output. The default configuration is input.

With the UploadConfiguration method, you can change the configuration of the binary I/Os. The configuration is a list of ChannelConfig structs. Each struct contains the channel number, the channel mode and its initial value. The channel number is 0-based. The channel mode is either ChannelMode_BINARYIOTYPEC_OUTPUT_PUSH_PULL or ChannelMode_BINARYIOTYPEC_INPUT_TYPE_1_3.

Channels that are not specified in the ChannelConfig list are not changed.

For example, to configure channel 0..3 as output and leave the rest of the channels unchanged, use the following code:

  channnelConfig := make([]*biniopb.ChannelConfig, 4)
  for i := 0; i < 4; i++ {
    channnelConfig[i] = &biniopb.ChannelConfig{
      Channel:      int32(i),
      Mode:         biniopb.ChannelMode_BINARYIOTYPEC_OUTPUT_PUSH_PULL,
      InitialValue: false,
    }
  }
  if err := c.UploadConfiguration(
    binio.WithChannelConfig(channnelConfig),
  ); err != nil {
    log.Fatalf("Failed to upload configuration: %v\n", err)
  }

With the upload_configuration method, you can change the configuration of the binary I/Os. For each channel you want to change, pass the channel number, the channel mode and its initial value. The channel number is 0-based. The channel mode is either BINARYIOTYPEC_OUTPUT_PUSH_PULL or BINARYIOTYPEC_INPUT_TYPE_1_3.

Channels that are not specified are not changed.

For example, to configure channel 0..3 as output and leave the rest of the channels unchanged, use the following code:

    config = binio.Pb.ConfigurationSet()
    for channel in range(4):
        config.channelConfig.add(
            channel=channel,
            mode=binio.Pb.ChannelMode.BINARYIOTYPEC_OUTPUT_PUSH_PULL,
            initialValue=False,
        )
    binio_client.upload_configuration(config)

Controlling Output Values

The API provides two methods to control channel output values

  • Control a single pin
  • Control multiple pins

Control a single pin:

    // output high value on first channel
    err = c.SetOutput(0, true)

Control multiple pins using a bit mask. The second parameter to SetAllOutputs is a mask that specifies which channels are affected:

    // set first binary output to high, set second output to low, don't change other channels
    err := c.SetAllOutputs(0x1, 0x3)

    // set first 4 channels to low, don't change other channels
    err := c.SetAllOutputs(0x0, 0xf)

The SetOuput and SetAllOutputs methods return an error if

  • the channel number is out of range
  • a channel that shall receive a new output value is configured as input
  • the channel’s group has no power

The actual pin state of channels configured as outputs can be read back using the Input and AllInputs methods below.

Control a single pin:

    # output high value on first channel
    binio_client.set_output(0, True)

Control multiple pins using a bit mask. The second parameter to set_all_outputs is a mask that specifies which channels are affected:

    # set first binary output to high, set second output to low, don't change other channels
    binio_client.set_all_outputs(0x1, 0x3)

    # set first 4 channels to low, don't change other channels
    binio_client.set_all_outputs(0x0, 0xf)

The set_output and set_all_outputs methods raise a RuntimeErrpr if

  • the channel number is out of range
  • a channel that shall receive a new output value is configured as input
  • the channel’s group has no power

The actual pin state of channels configured as outputs can be read back using the input and all_inputs methods below.

Output Watchdog

By default, the outputs keep their commanded state forever, even if the host program has terminated or crashed.

To ensure that outputs are turned off in such cases, the firmware implements a watchdog functionality. The watchdog can be enabled per channel and the watchdog timeout is configurable (but is the same for all channels).

    // set 2 seconds watchdog on first channel, but not on other channels.
    // The first parameter is a bit mask that specifies the channels that are affected.
    if err := c.UploadConfiguration(binio.WithOutputWatchdog(0x1, 2000)); err != nil {
      log.Fatalf("Failed to set configuration: %v\n", err)
    }

    config = binio.Pb.ConfigurationSet()
    # outputWatchdogMask is a bit mask that specifies the channels that are affected.
    config.outputWatchdogMask = 0x1 # enable watchdog for channel 0
    config.outputWatchdogTimeout = 2000
    config.changeOutputWatchdog = True
    binio_client.upload_configuration(config)

With that setting, the host must periodically set each of the enabled channels to the active value (the opposite of the inactive value) within 2 seconds. If the host does not set the channel within the watchdog timeout, the firmware sets back the channel to its initial value.

Overcurrent and Overload Handling

The channel outputs are overcurrent and overload protected. In case an overcurrent condition is detected on one output, the channel limits the current to its maximum (300mA for high side switch, 200mA for low side switch).

In addition, the binary outputs detect thermal overload condition. In this case the channel is disabled until the channel’s temperature falls below a certain threshold, then the channels output is activated again.

Overcurrent and overload conditions are reported via the diagnostic values returned by the Input and AllInputs method.

Overcurrent and overload conditions are reported via the diagnostic values returned by the input and all_inputs method.

Reading Inputs and Channel Diagnostics

The API provides two methods to read the current state of the pins:

  • Get value of a single pin
  • Get value of multiple pins
    // read state of first channel
    // value will be true, if the level is above the input switching threshold
    // diag returns the diagnostic value
    value, diag, err := c.Input(0)

    // check for channel diagnostics
    if diag&uint32(biniopb.ChannelDiag_CurrentLimit) != 0 {
      // channel is in current limit state
    }
    if diag&uint32(biniopb.ChannelDiag_NoSupplyVoltage) != 0 {
      // channel's group has no supply voltage
    }

    // read state of all channels.
    // values contains then a bit mask with the state of each input
    // diag is a list of diagnostic values, one for each channel
    values, diag, err := c.AllInputs()

    // check for diagnostics of second channel
    if diag[1]&uint32(biniopb.ChannelDiag_CurrentLimit) != 0 {
      // channel is in current limit state
    }

The diagnostic value(s) contain a bit mask with the following flags:

  • ChannelDiag_NoSupplyVoltage: The channel’s group has no power
  • ChannelDiag_CurrentLimit: The channel is in current limit mode
  • ChannelDiag_Overload: The channel is in overload mode
  • ChannelDiag_SupplyUndervoltage: The channel’s supply voltage is below the minimum voltage (<17V)
  • ChannelDiag_SupplyOvervoltage: The channel’s supply voltage is above the maximum voltage (>43V). However, this flag is never set as long as the hardware isn’t damaged.
    # read state of first channel
    # state will be true, if the level is above the input switching threshold
    # diag returns the diagnostic value
    state, diag = binio_client.input(0)

    # check for channel diagnostics
    if diag&binio.Pb.ChannelDiag.NoSupplyVoltage != 0:  TODO
      # channel's group has no supply voltage

    # read state of all channels.
    # all.inputs contains then a bit mask with the state of each input
    # all.diag is a list of diagnostic values, one for each channel
    all = binio_client.all_inputs()
    for channel in range(n_channels):
        state = 1 if all.inputs & (1 << channel) else 0
        print("  Ch%d state=%d diag=0x%x" % (channel, state, all.diag[channel]))

The diagnostic value(s) contain a bit mask with the following flags:

  • NoSupplyVoltage: The channel’s group has no power
  • CurrentLimit: The channel is in current limit mode
  • Overload: The channel is in overload mode
  • SupplyUndervoltage: The channel’s supply voltage is below the minimum voltage (<17V)
  • SupplyOvervoltage: The channel’s supply voltage is above the maximum voltage (>43V). However, this flag is never set as long as the hardware isn’t damaged.

Input Transient Recording

In data logger applications, you may want to record changes of the channels.

Therefore, the API provides functions to start a Stream. At stream creation, you select the channels which you want to monitor for changes.

The MIO07 samples the channel values at a rate of 1.25kHz, so the timestamps are accurate to 800us.

// start stream, watch for changes on first two channels
err = c.StartStream(binio.WithChannelFilterMask(0x3))

For each transition, a Sample is generated in the stream, each sample contains:

  • A timestamp of the transition
  • The value of all channels specified by ChannelFilterMask at the time of the transition.
  • A bit mask that indicates if the corresponding channel value is valid. (channels not in ChannelFilterMask are always flagged invalid).

For efficiency, multiple samples are gathered and sent as one Bucket to the host. To read samples from the stream:

  firstTs := uint64(0)
  for {
    // read next bucket from stream
    sd, err := c.ReadStream(time.Second * 5)

    if err != nil {
      log.Fatalf("ReadStreamData failed: %v\n", err)
    } else {
      samples := sd.FSData.GetSamples()
      log.Printf("got stream data seq=%d ts=%d samples=%d\n", sd.Sequence, sd.DeliveryTimestamp, len(samples))

      for i, sample := range samples {
        if firstTs == 0 {
          firstTs = sample.Timestamp
        }
        log.Printf("sample %d: relTs=%10dus values=b%016b valid=b%016b", i, sample.Timestamp-firstTs, sample.Values, sample.ValueValid)
      }
    }
  }

    # start stream, watch for changes on first two channels

    binio_client.start_stream(
        binio.Pb.StreamControlStart(channelFilterMask=0x0003),
        fb.Pb.StreamControlStart(
            bucketSamples=25,
            keepaliveInterval=1000,
            bufferedSamples=50,
            low_latency_mode=True,
        ),
    )

For each transition, a Sample is generated in the stream, each sample contains:

  • A timestamp of the transition
  • The value of all channels specified by ChannelFilterMask at the time of the transition.
  • A bit mask that indicates if the corresponding channel value is valid. (channels not in ChannelFilterMask are always flagged invalid).

For efficiency, multiple samples are gathered and sent as one Bucket to the host. To read samples from the stream:

    for _ in range(10):
        generic_stream_data, stream_data = binio_client.read_stream()
        print(
            f"Received stream data {generic_stream_data.deliveryTimestampUs}, {generic_stream_data.sequence}"
        )
        for sample in stream_data.samples:
            print(" Time=%d Inputs=0x%x Valid=0x%x" % (sample.timestamp, sample.values, sample.value_valid))

NOTE: At the moment, timestamps are expressed in micro seconds relative to the start of the MIO07. Future client libraries will map the time to the host’s time domain

Controlling the Stream

The stream behavior can be fine-tuned to the application needs. If you do not specify any parameters, the default values are used.

  • The BucketSamples parameter (default: 25) defines the number of samples per bucket. If the bucket contains BucketSamples, it is sent to the client.

  • The KeepAliveInterval parameter (default: 1000) defines the maximum time in ms between two buckets. If the bucket is not full, it is sent after the configured interval.

  • The BufferedSamples parameter (default: 50) defines the number of samples that can be buffered in the device. If the buffer is full, the oldest samples are overwritten. As a rule of thumb, BufferedSamples should be at least two times the BucketSamples. Select a higher number if your reception process is slow to avoid buffer overruns.

  • If you want low latency on the received data, you can enable the “low latency” mode by using LowLatencyMode (default: false). In this mode, samples are sent as soon as possible after they have been received. This means that the buckets contain 1..BufferedSamples samples.

  // configure stream to send the bucket at least once a second
  // configure the maximum samples per bucket to 25
  // configure low latency mode
  // configure the buffered samples to 200
  err = c.StartStream(
      binio.WithFBStreamOption(functionblock.WithKeepaliveInterval(1000)),
      binio.WithFBStreamOption(functionblock.WithBucketSamples(25)),
      binio.WithFBStreamOption(functionblock.WithLowLatencyMode(true))
      binio.WithFBStreamOption(functionblock.WithBufferedSamples(200)),
  )

The stream behavior can be fine-tuned to the application needs:

  • The bucketSamples parameter defines the number of samples per bucket. If the bucket contains bucketSamples, it is sent to the client.

  • The keepAliveInterval parameter defines the maximum time in ms between two buckets. If the bucket is not full, it is sent after the configured interval.

  • The bufferedSamples parameter defines the number of samples that can be buffered in the device. If the buffer is full, the oldest samples are overwritten. As a rule of thumb, bufferedSamples should be at least two times the bucketSamples. Select a higher number if your reception process is slow to avoid buffer overruns.

  • If you want low latency on the received data, you can enable the “low latency” mode by setting low_latency_mode to True. In this mode, samples are sent as soon as possible after they have been received. This means that the buckets contain 1..bufferedSamples samples.

    binio_client.start_stream(
        binio.Pb.StreamControlStart(channelFilterMask=0x0003),
        fb.Pb.StreamControlStart(
            bucketSamples=25,
            keepaliveInterval=1000,
            bufferedSamples=50,
            low_latency_mode=True,
        ),
    )

Multiple Clients

It is possible to have multiple clients. Example usage:

  • Each client has its own stream. One client may have a stream that records transitions on channel #1, while another client records transitions on channel #2, #3 and #4.
  • One client is reading the current state of the channels, while another client is recording transitions and a third client is writing to a channel.